Friedrich PDH07R3SG Brochure download pdf (Page 4)

STANDARD GRILLE

PXGA

Standard, stamped, anodized aluminum to resist chalking

and oxidation.

ARCHITECTURAL GRILLES

Architectural grilles that consist of heavy gauge 6063-T5 aluminum alloy

PXAA Clear extruded aluminum.

PXBG Beige acrylic enamel.

PXSC Available in custom colors.

DECORATIVE SUBBASE (black)

PXSBA

Provides unit support for walls less than six inches thick. Includes leveling

legs, side ller panels and mounting brackets for electrical accessories.

Accepts circuit breaker, power disconnect switch and conduit kit.

ELECTRICAL SUBBASE

Provides unit support for walls less than six

inches thick. Includes leveling legs, side

ller panels, mounting brackets, a plug-in

receptacle and eld-wiring access. The sub-

base also includes electrical knockouts for a

power disconnect switch or circuit breaker.

POWER CORDS

PXFTA

Antimicrobial air lters. 10 pack.

CONDENSATE DRAIN KIT

PXDR10

Attaches to the bottom of the wall sleeve for internal draining of condensate

or to the rear wall sleeve ange for external draining. Recommended for all

units to remove excess condensate. 10 pack.

LATERAL DUCT ADAPTER

PDXDAA

Attaches to the Friedrich PTAC/PTHP unit to direct up to 35% of the total

airow to a second room. The unit-mounted duct plenum features a front-

mounted aluminum grille that has two positions to provide the most optimal

air direction. The air may be directed to either the left or the right of the

unit through the supplied 3.5 H" x 7 W" x 47" L plenum. Plenum may be cut

to length by the installer. Kit includes duct plenum, front grille, 47" duct

extension, duct discharge grille, duct end cap and all necessary mounting

hardware.

LATERAL DUCT EXTENSION

PDXDEA

Additional 3.5 H" x 7" W x 47" L plenum for use with the LATERAL DUCT

ADAPTER. A maximum of 3 duct extensions total may be used. Note:

Ducted airow is reduced as duct length is increased.

PXSB23020

Electrical Subbase - 230V 15 & 20A

PXSB23030

Electrical Subbase - 230V 30A

PXSB26515

Electrical Subbase - 265V 15A

PXSB26520

Electrical Subbase - 265V 20A

PXSB26530

Electrical Subbase - 265V 30A

OPTIONAL ACCESSORIES

RT6 WRT1

EMRT1, EMWRT1

PXAA

PDXDAA and PDXDEA ship together

OPTIONAL ACCESSORIES

WALL SLEEVE

PDXWSA

Galvanized steel is prepared in a state-of-the-art, multistep process for

stronger paint adhesion, then powder coated with a polyester finish and

cured in an oven for exceptional durability. The wall sleeve is insulated for

thermal efciency and noise reduction.

16" H x 42" W x 13 ¾" D

SLEEVE EXTENSION RETROFIT KIT

PXSE

2 ¼" sleeve extension attached to the room side of the sleeve to allow for the

installation of a PD-series Friedrich PTAC in a 11 ½" deep T-series sleeve.

DEEP WALL SLEEVES

PDXWSEXT18

For walls up to 17 1/2” deep.

PDXWSEXT24

For walls up to 23 1/2” deep.

PDXWSEXT (Custom depth wall sleeve)

One-piece extended wall sleeve for walls from 13 1/4" to 25 1/2" deep are

available by special order.

DIGITAL REMOTE THERMOSTAT

RT6

Single stage cool, single stage heat for PDE models or single stage cool, dual

stage heat for PDH model thermostat features high/low fan speed switch.

Thermostat is hard wired and can be battery powered or unit powered.

Features backlit display and multiple conguration modes.

WRT1

Wireless, single stage, wall-mounted digital thermostat with two fan

speeds. Features backlit display and multiple conguration modes.

FRIEDRICHLINK

ENERGY MANAGEMENT THERMOSTATS

EMRT1

Wired thermostat with occupancy sensor.

EMWRT1

Wireless thermostat with occupancy sensor.

EMOCT EMRAF

Online connection kit. Remote access fee.

REMOTE THERMOSTAT ESCUTCHEON KIT

PDXRTA

Kit contains escutcheons that can be placed over the factory control buttons

when a remote wall mounted thermostat is used. The escutcheon directs

the user to the wall thermostat for operation and retains the LED window to

display error codes and diagnostic information. 10 pack.

CONDUIT KIT /JUNCTION BOX

PXCJA

Hard wire conduit kit with junction box for 208/230V and 265V units (subbase

not required). Kit includes a means of quick disconnect for easy removal of the

chassis.

Length

PXPC23000 LCDI 230V 15A Cord - 00 kW (for use PDE models only) 6 ft.

PXPC23015 LCDI 230V 15A Cord - 2.0 kW 6 ft.

PXPC23020 LCDI 230V 20A Cord - 3.0 kW 6 ft.

PXPC23030 LCDI 230V 30A Cord - 5.0 kW 6 ft.

PXPC26515 Non-LCDI 265V 15A Cord - 2.0 kW 18 inches

PXPC26520 Non-LCDI 265V 20A Cord - 3.0 kW 18 inches

PXPC26530 Non-LCDI 265V 30A Cord - 5.0 kW 18 inches

Deep wall sleeve extension PDXWSEXT18 shown with

weather panel in place

1 2 3 4 5

Comments to this Manuals

No comments

Friedrich PDH07R3SG Brochure Page 4

Comments to this Manuals

Related products and manuals for Heat pumps Friedrich PDH07R3SG