920-087-02 (9-03)WallMaster® PTACPackaged Terminal Air Conditioners & Heat Pumps • Standard • Remote Thermostat • Seacoast ProtectedInstalla
10920-087-02 (9-03)11920-087-02 (9-03)Plastic handlesPlastic grommets1. Remove the center support and weatherboard if still installed in the sleeve.2
10920-087-02 (9-03)11920-087-02 (9-03)B. Electrical Rating TablesAll 230/208 volt units are equipped with power cords. See Appendix B on page 19 for w
12920-087-02 (9-03)13920-087-02 (9-03)Wall sleeveWeatherboardCenter supportSection III – Chassis Installation1. Remove the weatherboard and cente
12920-087-02 (9-03)13920-087-02 (9-03)4. Center the chassis in the pre-installed sleeve and carefully push the chassis until the chassis ange and ga
14920-087-02 (9-03)15920-087-02 (9-03)C. Standard Unit OperationRotate the temperature dial in small increments in the warmer or cooler direction. Mov
14920-087-02 (9-03)15920-087-02 (9-03)E. Heating Control (heat pumps and emergency heat operation)F. Fan Cycle SwitchThe fan cycle switch is located
16920-087-02 (9-03)17920-087-02 (9-03)H. Air Discharge GrilleThe air discharge grille can be redirected to blow air either straight up or at an angle
16920-087-02 (9-03)17920-087-02 (9-03)Typical PTAC/PTHP unitUsed for PTHP onlyWall thermostatNOTE: It is the installer's responsibility to ensur
18920-087-02 (9-03)19920-087-02 (9-03)Appendix A (continued)The simplified connection diagram at left shows the factory congured wiring set f
18920-087-02 (9-03)19920-087-02 (9-03)Appendix B: Electrical Wiring for 265 Volt Models1. Remove the four control box retaining screws (A) and open
2920-087-02 (9-03)3920-087-02 (9-03)Unit Components...
20920-087-02 (9-03)21920-087-02 (9-03)J. Routine Maintenance1. Clean the unit air intake lter at least every 300 to 350 hours of operation. Clean t
20920-087-02 (9-03)21920-087-02 (9-03)K. Basic Troubleshooting TechniquesBeing familiar with the sequence of operation on Standard Controlled Operatin
22920-087-02 (9-03)23920-087-02 (9-03)DESK CONTROL KIT A eld installed kit which allows the unit to be turned on or off from a remote central station
22920-087-02 (9-03)23920-087-02 (9-03)Friedrich PTAC Accessories (continued)PXSESLEEVE EXTENSION RETROFIT KIT G-90 zinc coated steel, 2.4"
SAVE THIS CERTIFICATE. It gives you specic rights, you may also have other rights which may vary from state to state and province to province.In the
2920-087-02 (9-03)3920-087-02 (9-03)Announcing the Friedrich P-Series Packaged Terminal Air Conditioner.A new approach to reliability and efciency.
4920-087-02 (9-03)5920-087-02 (9-03)PTAC Installation RecommendationsFor proper PTAC unit performance and maximum operating life please refer to the m
4920-087-02 (9-03)5920-087-02 (9-03)Installation Instructions PXDR10 Drain KitInternal Drain (optional for new construction)NOTE: If installing an in
6920-087-02 (9-03)7920-087-02 (9-03)External Drain (for new construction or unit replacement)When using an external drain system, the condensate is re
6920-087-02 (9-03)7920-087-02 (9-03)Wall Sleeve Installation Instructions (PXWS)NOTE: Insure that the unit is only installed in a wall structurally a
8920-087-02 (9-03)9920-087-02 (9-03)3. Drill two 3/16" holes through each side of the sleeve approximately 4" from top and 4&qu
8920-087-02 (9-03)9920-087-02 (9-03)If the wall is thicker than allowed in the notes in Figure 6, a sheet metal wall sleeve extension and ashing MUST
Comments to this Manuals