Friedrich EQ08 User Manual download pdf (Page 3)

920-197-01

For the best cooling performance and highest energy efficiency

Keep the filter clean

Make sure that your air conditioner is always in top performing condition by

retlifehtgninaelcdnagnivomerrofsnoit curts nI.ylralugerretlifehtgninaelc

can be found on page 6.

Provide good air flow

Make sure the airflow path to and from the unit is clear. Your air conditioner

puts the conditioned air out at the top of the unit, andtakes in unconditionedair

at the bottom. Airflow is critical to good operation. It is just as important on the

.dekcolbtonsiroiretxetinuehtdnuorawolfriaehttahtgni dliubehtfoedistuo

Unit placement

If your air conditioner canbe placedin a window or wall that is shaded by a tree

rosepardgnisU.yltneiciffeeromneveetarepolliwtinueht,gnidliubre hto naro

blinds on the sunny side of the dwelling will also add to your unit’s efficiency.

Make sure the wiring is adequate for your unit.

If you have fuses, they should be of the time delay type. Before you install

or relocatethisunit,besurethattheamperageratingofthecircuitbreaker

or time delay fuse does not exceed the amp rating listed in Figure 1.

DO NOT use an extension cord.

Thecordprovidedwillcarrytheproperamountofelectricalpowertothe

.tonlliwdrocnois net xena;tinu

Make sure that the receptacle is compatible with

the air conditioner cord plug provided.

This insures proper grounding. If you have a two prong receptacle you

willneedtohaveitreplacedwithagroundedreceptaclebyacerti¿ed

electrician. The grounded receptacle should meet all national and local

codes and ordinances. Under no circumstances should you remove the

ground prong from the plug. You must use the three prong plug furnished

with the air conditioner.

Test the power cord

All Friedrichroomair conditioners are shipped from thefactory with a Leakage

Current Detection Interrupter (LCDI) equipped power cord. The LCDI device

meets the UL and NEC requirements for cord connected air conditioners

effective August 2004.

To test your power supply cord:

1. Plug power supply cord into a grounded 3 prong outlet.

2. Press RESET (See Figure 2).

3. Press TEST (listen for click; Reset button trips and pops out).

4. Press and release RESET (listen for click; Reset button latches and

remains in). The power supply cord is ready for operation.

NOTE: LCDI device is not intended to be used as a switch.

Once plugged in, the unit will operate normally without the need to reset

the LCDI device.

Insulation

Good insulation will be a big help in maintaining desirable comfort levels.

Doors should have weather stripping. Be sure to caulk around doors and

windows.

Proper installation of seal gasket

Make sure the seal gasket has been installed properly to minimize noise and

improve ef¿ciency. If the seal gasket has not been installed, please refer to

installation instructions on page 8.

WARNING: Before operating your unit

MODEL

CIRCUIT RATING

OR TIME DELAY

FUSE

REQUIRED WALL

RECEPTACLE

AMP VOLT NEMA NO.

XQ0XQ06

XQ0XQ10

XQ12  EQ08

YQ07

15 125 5-15R

Figure 1

Figure 2

TEST

RESET

WARNING

TEST BEFORE EACH USE

1. PRESS RESET BUTTON

2. PLUG LDCI INTO POWER

RECEPTACLE

3. PRESS TEST BUTTON,

RESET BUTTON SHOULD

POP UP

4. PRESS TEST BUTTON,

FOR USE

DO NOT USE IF ABOVE TEST

FAILS

WHEN GREEN LIGHT IS ON

IT IS WORKING PROPERLY

RESET

TEST

NOTE: Your LCDI device will resemble one of these illustrations.

If the device fails to trip when tested or if the powersupply cord is damaged, it

must be replaced with a new supply cord from the manufacturer. We recom-

mend youcontactour Technical AssistanceLineat(800)541-6645ext.845.

To expedite service, please have your model and serial number available.

Electrical Shock Hazard

Make sure your electrical receptacle has the

same configuration as your air conditioner’s

plug. If different, consult a Licensed Electrician.

Do not use plug adapters.

Do not use an extension cord.

Do not remove ground prong.

Always plug into a grounded 3 prong outlet.

Failure to follow these instructions can result in

death, fire, or electrical shock.

WARNING

1 2 3 4 5 6 7 8 ... 39 40

Comments to this Manuals

No comments

Friedrich EQ08 User Manual Page 3

Comments to this Manuals

Related products and manuals for Unknown Friedrich EQ08