Friedrich EQ08 User Manual download pdf (Page 11)

920-197-01

Power failure

If you have a power failure,the unit's auto-restartfeature will resumeoperation

in the selected mode prior to the power failure.

Won't cool?

If your air conditioner operates, but won’t cool; check to see if the controls

are properly set. Check the filter and clean thoroughly if needed. Check to

see if the chassis seal gasket is installed (refer to Installation Instructions,

Step 8, page 8).

Won't run?

Make sure the power cord is plugged in completely. Check for a bad fuse,

tripped breaker or tripped LCDI Device. Refer to page 3 for LCDI reset

instructions and to con¿rm proper fuse size.

ForX-Starmodelsonly:

Youcanresetthecircuitboardbypressingthe“MODE”buttonandthe

“TEMPERATURE DOWN” button at the same time. The LEDs (small red

lights) for Hour, Start and Stop will begin blinking. Once this occurs, turn

the unit off by pressing the On/Off button once and then unplug the unit.

Finally, plug the unit back in and turn it on by pressing the On/Off button

once. All settings revert back to the factory default settings.

This is a warm weather appliance

Your air conditioner is designed to cool in warm weather when the outside

temperature is above 60°F (16°C), so it won't cool a room if it is already cool

outside. Also, it will not provide adequate heating when the outdoor ambient

temperature falls below 37°F (3°C).

Condensation is normal

Air conditioners actually pump the heat and humidity from your room to the

tsomesulliwrenoitidnocriaruoydna,retawsemoc ebytidimuH.riaedistuo

of the water to keep the outside coil cool. If there is excessive humidity, there

.noit a re polamronsisihT.edistuopirdlliwtahtretawssecxeebyam

Frosting

This usually occurs because of insufficient airflow across the coils, a dirty

ottinuteS.esehtfollaro,re htaewpmadlooc,retlif Fan Only and the frost

will disappear. Setting the thermostat a little warmer will probably prevent

the frosting from recurring.

Noises

All air conditioners make some noise. We build them to operate as quietly as

detnuomenonahtreteiuqsillawanidetnuomre noit id nocrianA.elbissop

in a window. It is important to ensure that the chassis seal gasket is properly

installed (refer to Installation Instructions, Step 8, page 8).

Cleaning your air conditioner

The decorative front and the cabinet can be cleaned with warm water and a

-hcattagnitsudahtiwdemuucavebnacliocroodniehT.tneg ret eddiuqildlim

ment if it appears to be dirty. The outdoor coil can be gently sprayed with a

hose if you can get to it. If not, you might call your dealer for a more thorough

cleaning when needed. The air ¿lter shouldbe inspected weeklyand cleaned

ifneededbyvacuumingwithadustattachmentorbycleaninginthesink

using warm water and a mild dishwashing detergent. Dry the ¿lter thoroughly

before reinstalling. Use caution– the coil surface can be sharp.

Heat pumps operate differently

Ifyourunitisa"Y",orheatpumpmodel,therearesomethingsthatyouwill

want to be aware of.

Somefunctionsofaheatpumpdifferfromyourunitwhenitisusedfor

cooling:

1. It is normal for ice to form on the outdoor coil of the heat pump.

Moisture in the outside air, passing over the coil when very cold,

will form ice.

2. If the outdoor temperature drops below 37°F (-3°C), your heat

nehW.taehecnat sis ercirtceleehtnonrutyllacitamotualliwpmup

the temperature rises to 40°F (4°C) , the compressor will resume

the heat pump operation. If your unit is a 115 volt model (YQ07), it

is designed for use in warmer climates and has no electrical heat

feature, and will not provide adequate heat below 37°F(3°C).

Troubleshooting tips

Window installation kits - heat pump models

Friedrich YQ Heat Pump models are normally installed thru-the-wall and

are packaged and sold without the expandable curtain assemblies. The

WIKQ Curtain Assembly Kit may be purchased as an accessory for window

installations. This accessory can be ordered from your Friedrich Dealer.

When ordering a kit, state model and serial number of your unit.

Available accessories

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 39 40

Comments to this Manuals

No comments

Friedrich EQ08 User Manual Page 11

Comments to this Manuals

Related products and manuals for Unknown Friedrich EQ08